Open-source IoT Platform

Device management, data collection, processing and visualization
for your IoT projects
Learn about Thingsboard

Thursday, January 5, 2017

ESP8266 GPIO control over MQTT using Thingsboard

Thingsboard is an open-source server-side platform that allows you to monitor and control IoT devices. It is free for both personal and commercial usage and you can deploy it anywhere. If this is your first experience with the platform we recommend to review what-is-thingsboard page and getting-started guide.

This sample application will allow you to control GPIO of your ESP8266 device using Thingsboard web UI. We will observe GPIO control using Leds connected to the pins. The purpose of this application is to demonstrate Thingsboard RPC capabilities.

The application that is running on ESP8266 is written using Arduino SDK which is quite simple and easy to understand. ESP8266 offers a complete and self-contained Wi-Fi networking solution. ESP8266 push data to Thingsboard server via MQTT protocol by using PubSubClient library for Arduino. Current GPIO state and GPIO control widget is visualized using built-in customizable dashboard.

The video below demonstrates the final result of this tutorial.





Prerequisites

You will need to Thingsboard server up and running. Use either Live Demo or Installation Guide to install Thingsboard.

List of hardware and pinouts

image

  • USB to TTL

    image

    image

  • Breadboard

  • 2 female-to-female jumper wires

  • 7 female-to-male jumper wires

  • 2 Leds

  • 3.3V power source (for example 2 AA batteries)

Wiring schemes

Programming/flashing schema

ESP8266 Pin USB-TTL Pin
ESP8266 VCC USB-TTL VCC +3.3V
ESP8266 CH_PD USB-TTL VCC +3.3V
ESP8266 GND (-) USB-TTL GND
ESP8266 GPIO 0 USB-TTL GND
ESP8266 RX USB-TTL TX
ESP8266 TX USB-TTL RX
LED 1 Pin USB-TTL Pin
cathode USB-TTL GND
LED 1 Pin ESP8266 Pin
anode ESP8266 GPIO 2

The following picture summarizes the connections for this project in programming/debug mode:

image

Final schema (Battery Powered)

ESP8266 Pin 3.3V power source
ESP8266 VCC VCC+
ESP8266 CH_PD VCC+
ESP8266 GND (-) VCC-
LED 1 Pin ESP8266 Pin
anode ESP8266 GPIO 2
LED 1 Pin 3.3V power source
cathode VCC-
LED 2 Pin ESP8266 Pin
anode ESP8266 GPIO 0
LED 2 Pin 3.3V power source
cathode VCC-

The final picture:

image

Thingsboard configuration

Note Thingsboard configuration steps are necessary only in case of local Thingsboard installation. If you are using Live Demo instance all entities are pre-configured for your demo account. However, we recommend to review this steps because you will still need to get device access token to send requests to Thingsboard.

Provision your device

This step contains instructions that are necessary to connect your device to Thingsboard.

Open Thingsboard Web UI (http://localhost:8080) in browser and login as tenant administrator

Goto “Devices” section. Click “+” button and create device with name “ESP8266 Demo Device”.

image

Once device created, open its details and click “Manage credentials”. Copy auto-generated access token from the “Access token” field. Please save this device token. It will be referred to later as $ACCESS_TOKEN.

image

Click “Copy Device ID” in device details to copy your device id to clipboard. Paste your device id to some place, this value will be used in further steps.

Provision your dashboard

This step contains instructions that are necessary to provision new dashboard with map widgets to Thingsboard.

Open “Terminal” and download file containing demo dashboard JSON:

curl -L https://thingsboard.io/docs/samples/esp8266/resources/esp8266_gpio_dashboard.json > esp8266_gpio_dashboard.json

Update dashboard configuration with your device Id (obtained in previous step) by issuing the following command:

sed -i "s/{DEVICE_ID}/<your device id>/" esp8266_gpio_dashboard.json

Obtain JWT token by issuing login POST command:

curl -X POST --header 'Content-Type: application/json' --header 'Accept: application/json' -d '{"username":"[email protected]", "password":"tenant"}' 'http://localhost:8080/api/auth/login'

You will receive response in the following format:

{"token":"$YOUR_JSON_TOKEN", "refreshToken": "$REFRESH_TOKEN"}

copy $YOUR_JSON_TOKEN to some place. Note that it will be valid for 15 minutes by default.

Execute dashboard upload command:

curl -X POST --header 'Content-Type: application/json' --header 'Accept: application/json' --header 'X-Authorization: Bearer $YOUR_JSON_TOKEN' -d "@esp8266_gpio_dashboard.json" 'http://localhost:8080/api/dashboard'

Programming the ESP8266

Step 1. ESP8266 and Arduino IDE setup.

In order to start programming ESP8266 device you will need Arduino IDE installed and all related software.

Download and install Arduino IDE.

After starting arduino, open from the ‘file’ menu the preferences.

image

Fill in the “Additional board managers URL” this url: http://arduino.esp8266.com/stable/package_esp8266com_index.json

Close the screen by the OK button.

Now we can add the board ESP8266 using the board manager.

Click in the menu tools the menu option Board: “Most likely Arduino UNO”. There you will find the first option “Board Manager”.

Type in the search bar the 3 letters ESP. Locate and click on “esp8266 by ESP8266 Community”. Click on install and wait for a minute to download the board.

image

Note that this tutorial was tested with the “esp8266 by ESP8266 Community” version 2.3.0.

In the menu Tools “Board “Most likely Arduino UNO” three new boards are added.

Select “Generic ESP8266 Module”.

Prepare your hardware according to the Programming/flashing schema. Connect USB-TTL adapter with PC.

Select in the menu Tools, port the corresponding port of the USB-TTL adapter. Open the serial monitor (by pressing CTRL-Shift-M or from the menu Tools). Set the key emulation to “Both NL & CR” and the speed to 115200 baud. This can be set in the bottom of terminal screen.

Step 2. Install Arduino libraries.

Open Arduino IDE and go to Sketch -> Include Library -> Manage Libraries. Find and install the following libraries:

Note that this tutorial was tested with the following versions of the libraries:

  • PubSubClient 2.6
  • ArduinoJson 5.8.0

Step 3. Prepare and upload sketch.

Download and open esp8266-gpio-control.ino sketch.

Note You need to edit following constants and variables in the sketch:

  • WIFI_AP - name of your access point
  • WIFI_PASSWORD - access point password
  • TOKEN - the $ACCESS_TOKEN from Thingsboard configuration step.
  • thingsboardServer - Thingsboard HOST/IP address that is accessable within your wifi network. Specify “demo.thingsboard.io” if you are using live demo server.
resources/esp8266-gpio-control.ino
#include <ArduinoJson.h>
#include <PubSubClient.h>
#include <ESP8266WiFi.h>

#define WIFI_AP "YOUR_WIFI_AP"
#define WIFI_PASSWORD "YOUR_WIFI_PASSWORD"

#define TOKEN "ESP8266_DEMO_TOKEN"

#define GPIO0 0
#define GPIO2 2

#define GPIO0_PIN 3
#define GPIO2_PIN 5

char thingsboardServer[] = "demo.thingsboard.io";

WiFiClient wifiClient;

PubSubClient client(wifiClient);

int status = WL_IDLE_STATUS;

// We assume that all GPIOs are LOW
boolean gpioState[] = {false, false};

void setup() {
  Serial.begin(115200);
  // Set output mode for all GPIO pins
  pinMode(GPIO0, OUTPUT);
  pinMode(GPIO2, OUTPUT);
  delay(10);
  InitWiFi();
  client.setServer( thingsboardServer, 1883 );
  client.setCallback(on_message);
}

void loop() {
  if ( !client.connected() ) {
    reconnect();
  }

  client.loop();
}

// The callback for when a PUBLISH message is received from the server.
void on_message(const char* topic, byte* payload, unsigned int length) {

  Serial.println("On message");

  char json[length + 1];
  strncpy (json, (char*)payload, length);
  json[length] = '\0';

  Serial.print("Topic: ");
  Serial.println(topic);
  Serial.print("Message: ");
  Serial.println(json);

  // Decode JSON request
  StaticJsonBuffer<200> jsonBuffer;
  JsonObject& data = jsonBuffer.parseObject((char*)json);

  if (!data.success())
  {
    Serial.println("parseObject() failed");
    return;
  }

  // Check request method
  String methodName = String((const char*)data["method"]);

  if (methodName.equals("getGpioStatus")) {
    // Reply with GPIO status
    String responseTopic = String(topic);
    responseTopic.replace("request", "response");
    client.publish(responseTopic.c_str(), get_gpio_status().c_str());
  } else if (methodName.equals("setGpioStatus")) {
    // Update GPIO status and reply
    set_gpio_status(data["params"]["pin"], data["params"]["enabled"]);
    String responseTopic = String(topic);
    responseTopic.replace("request", "response");
    client.publish(responseTopic.c_str(), get_gpio_status().c_str());
    client.publish("v1/devices/me/attributes", get_gpio_status().c_str());
  }
}

String get_gpio_status() {
  // Prepare gpios JSON payload string
  StaticJsonBuffer<200> jsonBuffer;
  JsonObject& data = jsonBuffer.createObject();
  data[String(GPIO0_PIN)] = gpioState[0] ? true : false;
  data[String(GPIO2_PIN)] = gpioState[1] ? true : false;
  char payload[256];
  data.printTo(payload, sizeof(payload));
  String strPayload = String(payload);
  Serial.print("Get gpio status: ");
  Serial.println(strPayload);
  return strPayload;
}

void set_gpio_status(int pin, boolean enabled) {
  if (pin == GPIO0_PIN) {
    // Output GPIOs state
    digitalWrite(GPIO0, enabled ? HIGH : LOW);
    // Update GPIOs state
    gpioState[0] = enabled;
  } else if (pin == GPIO2_PIN) {
    // Output GPIOs state
    digitalWrite(GPIO2, enabled ? HIGH : LOW);
    // Update GPIOs state
    gpioState[1] = enabled;
  }
}

void InitWiFi() {
  Serial.println("Connecting to AP ...");
  // attempt to connect to WiFi network

  WiFi.begin(WIFI_AP, WIFI_PASSWORD);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("Connected to AP");
}


void reconnect() {
  // Loop until we're reconnected
  while (!client.connected()) {
    status = WiFi.status();
    if ( status != WL_CONNECTED) {
      WiFi.begin(WIFI_AP, WIFI_PASSWORD);
      while (WiFi.status() != WL_CONNECTED) {
        delay(500);
        Serial.print(".");
      }
      Serial.println("Connected to AP");
    }
    Serial.print("Connecting to Thingsboard node ...");
    // Attempt to connect (clientId, username, password)
    if ( client.connect("ESP8266 Device", TOKEN, NULL) ) {
      Serial.println( "[DONE]" );
      // Subscribing to receive RPC requests
      client.subscribe("v1/devices/me/rpc/request/+");
      // Sending current GPIO status
      Serial.println("Sending current GPIO status ...");
      client.publish("v1/devices/me/attributes", get_gpio_status().c_str());
    } else {
      Serial.print( "[FAILED] [ rc = " );
      Serial.print( client.state() );
      Serial.println( " : retrying in 5 seconds]" );
      // Wait 5 seconds before retrying
      delay( 5000 );
    }
  }
}

Connect USB-TTL adapter to PC and select the corresponding port in Arduino IDE. Compile and Upload your sketch to device using “Upload” button.

After application will be uploaded and started it will try to connect to Thingsboard node using mqtt client and upload current GPIOs state.

Autonomous operation

When you have uploaded the sketch, you may remove all the wires required for uploading including USB-TTL adapter and connect your ESP8266 and LEDs directly to power source according to the Final wiring schema.

Troubleshooting

In order to perform troubleshooting you should assemble your hardware according to the Programming/flashing schema. Then connect USB-TTL adapter with PC and select port of the USB-TTL adapter in Arduino IDE. Finally open “Serial Monitor” in order to view debug information produced by serial output.

Data visualization

Finally, open Thingsboard Web UI. You can access this dashboard by logging in as a tenant administrator.

In case of local installation:

In case of live-demo server:

  • login: your live-demo username (email)
  • password: your live-demo password

See live-demo page for more details how to get your account.

Once logged in, open Dashboards->ESP8266 GPIO Demo Dashboard page. You should observe demo dashboard with GPIO control and status panel for your device. Now you can switch status of GPIOs using control panel. As a result you will see LEDs status change on device and on the status panel.

Below is the screenshot of the “ESP8266 GPIO Demo Dashboard”.

image

Next steps

Browse other samples or explore guides related to main Thingsboard features:

Your feedback

If you found this article interesting, please leave your feedback in the comments section, post questions or feature requests on the forum and “star” our project on the github in order to stay tuned for new releases and tutorials.

17 comments :

  1. Can you show us how to do it using an Arduino? Thank you a lot!

    ReplyDelete
  2. curl -X POST --header 'Content-Type: application/json' --header 'Accept: application/json' --header 'X-Authorization: Bearer $YOUR_JSON_TOKEN' -d "@esp8266_gpio_dashboard.json" 'http://localhost:8080/api/dashboard'


    Getting Error After applying above command :

    {"status":401,"message":"Invalid username or password","errorCode":10,"timestamp":1550819762513}

    ReplyDelete
  3. Connecting to ThingsBoard node ...[FAILED] [ rc = -2 : retrying in 5 seconds]

    ReplyDelete
  4. What a fantabulous post this has been. Never seen this kind of useful post. I am grateful to you and expect more number of posts like these. Thank you very much. centralina aggiuntiva opel

    ReplyDelete
  5. Very informative post! There is a lot of information here that can help any business get started with a successful social networking campaign. spy phone app

    ReplyDelete
  6. I visit toiphone Store and here someone told me about thingsboard. Thingsboard is an open source platform that allows you to monitor and control IoT devices. It is free for both personal and commercial usage.

    ReplyDelete
  7. It will reduce stress very effectively vampire survivors. Have a nice day

    ReplyDelete
  8. Xiaomi phones in Canada are game-changers! With their cutting-edge features, sleek design, and affordable prices, they're taking the smartphone market by storm. I'm loving the Xiaomi experience, and it's great to see more options in the Canadian market!

    ReplyDelete
  9. Thingsboard unlocks the potential of GPIO control via MQTT! Dive into the realm of seamless connection between your devices and the Thingsboard platform, guided by Solo Lisa through the complexities of managing General Purpose Input/Output. With this meta description, you can enhance your IoT experience and have access to efficient, real-time control!Thank you for sharing your knowledge! Keep up the good job! Continue to spread the word. Please take a peek at my website.
    truck accident attorney near me

    ReplyDelete
  10. Efficiently manage ESP8266 GPIO pins through MQTT integration with Thingsboard, enabling seamless communication and control for IoT applications.Lawyers in new york||Lawyers in new jersey Harness the power of ESP8266 to manipulate GPIO states effortlessly via MQTT, seamlessly connecting with Thingsboard for streamlined monitoring and control in IoT environments.

    ReplyDelete

  11. Controlling GPIO pins on an ESP8266 device using MQTT (Message Queuing Telemetry Transport) via Thingsboard minecraftle involves several steps.

    ReplyDelete
  12. Tastings at breweries are like gourmet adventures where you get to sample a variety of wonderful tiger exchange or beers. It's an enjoyable opportunity to sample new cuisines and socialize with like-minded individuals. Toast to tastings at breweries!

    ReplyDelete