Open-source IoT Platform

Device management, data collection, processing and visualization
for your IoT projects
Learn about Thingsboard

Monday, December 19, 2016

Temperature upload over MQTT using NodeMCU and DHT11 sensor

Thingsboard is an open-source server-side platform that allows you to monitor and control IoT devices. It is free for both personal and commercial usage and you can deploy it anywhere. If this is your first experience with the platform we recommend to review what-is-thingsboard page and getting-started guide.

This sample application performs collection of temperature and humidity values produced by DHT11 sensor. Collected data is pushed to Thingsboard for storage and visualization. The purpose of this application is to demonstrate Thingsboard data collection API and visualization capabilities.

The DHT11 sensor is connected to NodeMCU. NodeMCU push data to Thingsboard server via MQTT protocol. Data is visualized using built-in customizable dashboard. The application that is running on NodeMCU is written using Lua scripting language which is quite simple and easy to understand.

Once you complete this sample/tutorial, you will see your sensor data on the following dashboard.

image

Prerequisites

You will need to Thingsboard server up and running. Use either Live Demo or Installation Guide to install Thingsboard.

List of hardware and pinouts

image

image

  • 3 female-to-female jumper wires

Wiring schema

image

NodeMCU Pin DHT-11 Pin
NodeMCU 3.3V DHT-11 VCC
NodeMCU GND DHT-11 GND (-)
NodeMCU D5 DHT-11 Data (S)

Programming the NodeMCU device

We need to download and build firmware with Lua interpreter for NodeMCU. This process is described in official documentation and there are multiple way to do this. You can use cloud build service for this purpose, however, we will use Docker Image.

Firmware download

Use following commands to clone official github repository for NodeMCU firmware.

$ mkdir -p ~/samples/nodemcu
$ cd ~/samples/nodemcu
$ git clone https://github.com/nodemcu/nodemcu-firmware.git

There is ability to customize firmware by changing two files:

  • ~/samples/nodemcu/nodemcu-firmware/app/include/user_config.h - There is an ability to change default baud rate in.

Please find and update line below to specify custom baud rate.

...
#define BIT_RATE_DEFAULT BIT_RATE_115200
...
  • ~/samples/nodemcu/nodemcu-firmware/app/include/user_modules.h - Contains list of what kind of modules included by default.

In our case all necessary modules included by default. However, please check that these modules are uncommented.

...
define LUA_USE_MODULES_DHT
...
define LUA_USE_MODULES_MQTT
...

Building firmware using Docker

The easiest way to build nodemcu firmware is by using prepared docker container for that task.

Please visit docker installation page and install docker on your machine.

After installation you need to download docker image from docker hub by command:

$ sudo docker pull marcelstoer/nodemcu-build 

Eventually build the firmware by next command:

$ sudo docker run --rm -ti -v ~/samples/nodemcu/nodemcu-firmware:/opt/nodemcu-firmware marcelstoer/nodemcu-build

As the result binary firmware located in the ~/samples/nodemcu/nodemcu-firmware/bin folder.

Application source code

Our application consists of three .lua files:

  • config.lua - configuration file, where we define custom configuration. You need to modify this file in order to setup your wifi network parameters and address of Thingsboard server.
    • your wifi network SSID - name of the wifi network.
    • your wifi network password - password to the network.
    • thingsboard server ip - host where your thingsboard installation. Use “demo.thingsboard.io” if you are using live demo server.
    • thingsboard mqtt port - 1883 is the default value.
    • thingsboard access token - DHT11_DEMO_TOKEN is the default value that corresponds to pre-provisioned demo account.

    If you are using live demo server - get the access token for pre-provisioned “DHT11 Demo Device”.

  • dht11.lua - sending temperature and humidity every 10 seconds to thingsboard server via MQTT protocol.
  • init.lua - initalization file that contains config.lua:
resources/config.lua
wifi_mode = 1
wifi_ssid = "YOUR_WIFI_SSID_HERE"
wifi_pass = "YOUR_WIFI_PASSWORD_HERE"
mqtt_ip = "YOUR_THINGSBOARD_HOST_OR_IP_HERE"
mqtt_port = 1883
access_token = "DHT11_DEMO_TOKEN"

Flashing the firmware

Before flashing firmware we need to figure out what serial interface using to communicate with NodeMCU.

$ dmesg
...
[845270.901509] usb 3-3: ch341-uart converter now attached to ttyUSB0
...

In our case /dev/ttyUSB0 is used for communication.

In order to flash firmware for NodeMCU, please download and install following utilities

Upload nodemcu firmware using command:

$ sudo ./esptool.py -b 115200 write_flash --flash_mode dio --flash_size 32m 0x0 ~~/samples/nodemcu/nodemcu-firmware/bin/nodemcu_integer_master_*.bin --verify

Upload application files using following commands:

$ sudo ./luatool.py --port /dev/ttyUSB0 -b 115200 --src config.lua --dest config.lua -v
$ sudo ./luatool.py --port /dev/ttyUSB0 -b 115200 --src dht11.lua --dest dht11.lua -v
$ sudo ./luatool.py --port /dev/ttyUSB0 -b 115200 --src init.lua --dest init.lua -v

Troubleshooting

Sometimes you can observe frequent blinking of the blue led after firmware upload. This is probably related to missing initialization data. Use following command to fix this:

$ sudo ./esptool.py -b 115200 write_flash --flash_mode dio --flash_size 32m 0x3fc000 ~/samples/nodemcu/nodemcu-firmware/bin/esp_init_data_default.bin --verify

Sometimes you are not able to upload lua files. Try to reset device and executing command again within first 10 seconds after reset. If no success, try to delete init.lua code from NodeMCU:

$ sudo ./luatool.py --port /dev/ttyUSB0 -b 115200 --delete init.lua

Data visualization

In order to simplify this guide we have included “Temperature & Humidity Demo Dashboard” to the demo data that is available in each Thingsboard installation. Of course, you can modify this dashboard: tune, add, delete widgets, etc. You can access this dashboard by logging in as a tenant administrator. Use

in case of local Thingsboard installation.

Once logged in, open Dashboards->Temperature & Humidity Demo Dashboard page. You should observe demo dashboard with live data from your device (similar to dashboard image in the introduction).

Next steps

Browse other samples or explore guides related to main Thingsboard features:

Your feedback

If you found this article interesting, please leave your feedback in the comments section, post questions or feature requests on the forum and “star” our project on the github in order to stay tuned for new releases and tutorials.

10 comments :

  1. Prepare yourself to take your wardrobe for an overhaul without breaking the bank because of a wonderful piece of information – it is time to know about cider coupon code! It does not matter whether you fancy classic elegance, current fads, and casual chic. Check your chosen brand’s website, subscribe to its email newsletter, or keep abreast with its social media posts for these exclusive stylish offers by your favorite ladies’ wear manufacturers. Affordable high quality fashions are just few button presses. Pass on, your fashion discoveries, coupon/promo codes, and style notes to the community, and let’s help/empower each other to look fabulous for cheaper, better, and faster! Therefore, why don’t you do something

    ReplyDelete
    Replies
    1. Your ability to connect seemingly disparate elements within this theme is a true testament to your creative genius, resulting in geometry dash a comprehensive and holistic understanding that enriches the reader's perspective.

      Delete
  2. I rely on BetGuru 365 for their comprehensive and honest assessments of betting sites. Their detailed reviews, available at https://betguru365.com/ , provide an unparalleled depth of analysis. They meticulously examine each site’s offerings, from odds and markets to security measures. This dedication to providing accurate and trustworthy reviews makes BetGuru 365 an essential tool for anyone interested in online betting.

    ReplyDelete
  3. Uploading temperature via MQTT using NodeMCU and DHT11 sensors has greatly improved access speed. eggy car

    ReplyDelete
  4. The technology of their numbers is amazing Head Soccer

    ReplyDelete
  5. To upload temperature data over MQTT Bou's Revenge using a NodeMCU and a DHT11 sensor, you'll need to set up your hardware and software properly.

    ReplyDelete
  6. Thank you so much sharing article you always sharing very informative article which help new students thank you so much.

    Free Coupon Codes & Discounts

    ReplyDelete
  7. Purchasing a GPS tracker is mostly done for real-time tracking. Different tracking devices have different real-time GPS tracking capabilities. doodle baseball

    ReplyDelete
  8. The significant improvement in access speed via MQTT using NodeMCU and DHT11 sensors has greatly improved access speed. geometry dash

    ReplyDelete
  9. Real-time monitoring and effective IoT communication are made possible by uploading temperature data over MQTT with a NodeMCU and a DHT11 sensor. This configuration offers a dependable means of sending environmental data to distant servers for control and analysis. I’m currently working on my master dissertation and I am really starting to feel the pressure. I have been think about whether I should buy master dissertation help to ensure everything is perfect. Has anyone here tried this? Was it helpful for your dissertation process? All I want to do is make sure I am receiving what I need without missing any vital. If anyone has used this before, please let me learn how it was and if you believe it is worth the cost.

    ReplyDelete